Prices and Services

Our rates are consistent with or lower than the national averages as per the Brownell’s Survey.

*All prices are for estimate purposes only and can vary depending on the details of your particular situation.

**Any prices and services not mentioned can be quoted.

 
 
780236.jpg

FULL MAINTENANCE

Consists of completely stripping the gun, cleaning all the parts, checking for wear, and making suggestions to the customer of services needed to put gun in A-1 condition: $50.00 (In the event that excessive fouling/damage is encountered, extra charges may apply. Contact us for more info).

 
969554.jpg

METAL REFINISHING

All metal refinishing is by estimate only. We offer Duracoating. We do NOT currently offer hot bluing.

 
sight-work.jpg

SIGHT WORK

  • Sight in customer gun: $60.00 (not including cost of ammo, targets, etc.)

  • Bore sighting customer gun: $25.00

  • Pattern shotgun: $60.00 (not including cost of ammo, targets, etc.)

  • Drill and tap barrel or receiver for sights: $40.00-$60.00

  • Drill and tap for scope mount: $60

  • Cut dovetail in barrel: $50.00

  • Install front sight ramp: $50.00-$75.00

  • Scope mounting: $35.00 (not including drill and tap)

 
general-barrel.jpg

GENERAL BARREL, ACTION, AND RIFLE WORK

  • Check headspace: $50.00

  • Make chamber cast: $50.00

  • Remove stuck fired case from chamber: hourly rate

  • Remove live round from chamber: $70.00

  • Remove obstruction from bore: hourly rate

  • Cut and crown barrel: hourly rate

  • Lap in bolt lugs: $50.00

  • Welding on new bolt handle: $100.00

  • Making and installing spring: hourly rate

  • Safeties installing: hourly rate

  • Trigger installation or adjustment: $50.00-$250.00

  • Installing barrel band swivel: hourly rate

 
muzzle-loader.gif

MUZZLE LOADER WORK

  • Pull ball: hourly rate

  • Remove broken ramrod from barrel: $25.00-$100.00

  • All other work: hourly rate

 
handgun.jpg

HANDGUN WORK

  • Chamfer revolver barrel: $50.00

  • Chamfer revolver cylinder: $60.00

  • Revolver action job: $50.00-$100.00 (clean, smooth action, not including replacement of parts)

  • Re-barrel revolver: $60.00-$100.00 (remove old barrel, replace with new factory barrel, labor only)

  • Straighten crane on revolver: $50.00

  • Install crane lock: $50.00

  • Remove/modify revolver hammer spur: hourly rate

  • Convert revolver from square to round butt: $65.00

  • Semi-auto pistol action job: $50.00-$150.00 (clean, smooth action, not including any parts)

  • Bevel mag. well: hourly rate

  • Cut slide for dovetail front sight: $50.00 (without cost of sight)

  • Cut slide for Novak rear: $145.00 (without cost of sight)

 
stock-work.jpg

SIGHT WORK

  • Wood finishing: $100.00 (does not include any shaping)

  • Recutting checkering: hourly rate

  • Glass bedding barrel and action: $70.00-$225.00

  • Install recoil pad: $50.00 (labor only)

  • Install adjustable butt plate: $50.00 (labor only)

  • Install sling swivels: $50.00

  • Install stock cross bolt: $50.00 (not including refinishing)

  • Install recoil reducer: $25.00-$125.00

  • Inletting and finishing of semi-finished stock: $200.00-$575.00 (not including checkering, recoil pad, special butt plate, grip cap, or other attachments)

  • Install adjustable comb hardware: $125.00-$235.00